D-Link DIR-810L rev B1

From WikiDevi.Wi-Cat.RU
Jump to navigation Jump to search

D-Link DIR-810L B1
Availability: now

Manuf (OEM/ODM): Cameo

FCC approval date: 05 March 2013
(Est.) release date: 11 April 2013
UPC: 790069390296 (UPC DB, On eBay)
Country of manuf.: China

Amazon image

ASIN
B00C9V0OBI (Flag of the United States.svg, On Amazon, On CCCmultiple uses)
multiple revisions of this device, use caution

Type: wireless router

FCC ID: KA2IR810LB1
IC ID: 4216A-IR810LB1

Power: 12 VDC, 1 A
Connector type: barrel

CPU1: MediaTek MT7620A (580 MHz)
FLA1: 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (Macronix MX25L6406EM2I-12G)
RAM1: 64 MiB67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (ESMT M14D5121632A-2.5B)

Expansion IFs: none specified
Serial: yes, 4-pad header, J1, (57600,8,N,1)

WI1 chip1: MediaTek MT7620A
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: none
WI2 chip1: MediaTek MT7610E
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 1x1:1
WI2 antenna connector: U.FL

ETH chip1: MediaTek MT7620A
Switch: MediaTek MT7620A
LAN speed: 100M
LAN ports: 4
WAN speed: 100M
WAN ports: 1

abgn+ac

TPFirmware supported: OpenWrt • (List | Dev | DLs)

Default SSID: dlink-XXXX (35 addl. devices)
, dlink-XXXX-5GHz (5 addl. devices)
Default IP address: 192.168.0.1
the IP 192.168.0.1 is used by 785 additional devices
of which 220 are D-Link devices
Default login user: Admin
Default login password: blank
Admin:blank credentials used by 84 additional devices
of which 79 are D-Link devices

802dot11 OUI: 6C:19:8F (2 E, -)
Ethernet OUI: 6C:19:8F (2 E, -)

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.


Wireless AC750 Dual Band Cloud Router

PCB rev B1 image

Boot Log

 • boot log
U-Boot 1.1.3 (Jun 10 2014 - 18:41:01)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83f98000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c2 20 17 c2 20 (2017c220)
find flash: MX25L6405D

MAC: 6c:19:8f:ed:f0:f6
==============================
Ralink UBoot Version: 4.1.1.0
DIR-810L(1.00b03)
------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jun 10 2014  Time:18:41:01
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes

3: System Boot system code via Flash.
## Booting image at bc170000 ...
   Image Name:   Linux Kernel Image
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    6047003 Bytes =  5.8 MB
   Load Address: 80000000
   Entry Point:  8000c2d0
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c2d0)
## Giving linux memsize in MB, 64

Starting kernel ...
LINUX started...

 THIS IS ASIC
init started: BusyBox v1.12.1 (2014-06-11 14:51:50 CST)
starting pid 35, tty '': '/etc_ro/rcS'
mount: mounting none on /proc/bus/usb failed: No such file or directory
Welcome to
    _______  _______  ___     __  ____   _  _   ___
    |  ___  \|   __  ||   |   |__||    \ | || | /  /
    | |___| ||  |__| ||   |__  __ |     \| || |/  /
    |   _   /|   _   ||      ||  || |\     ||     \
    |__| \__\|__| |__||______||__||_| \____||_|\___\

                     =System Architecture Department=

mount mydlink ok
mount flash ok
old language pack not found
language pack exists
Starting loop GPIO LED=9,PBC=2
Waiting for Wireless Events from interfaces...
[    leobox_ipc.c:  207       sem_create()]:::add semid = 0
[    leobox_ipc.c:  207       sem_create()]:::add semid = 32769
[    leobox_ipc.c:  207       sem_create()]:::add semid = 65538
[    leobox_ipc.c:  207       sem_create()]:::add semid = 98307
[    leobox_ipc.c:  207       sem_create()]:::add semid = 131076
[    leobox_ipc.c:  207       sem_create()]:::add semid = 163845
[    leobox_ipc.c:  207       sem_create()]:::add semid = 196614
[    leobox_ipc.c:  207       sem_create()]:::add semid = 229383
[    leobox_ipc.c:  207       sem_create()]:::add semid = 262152
[    leobox_ipc.c:  207       sem_create()]:::add semid = 294921
[    leobox_ipc.c:  207       sem_create()]:::add semid = 327690
[    leobox_ipc.c:  207       sem_create()]:::add semid = 360459
[    leobox_ipc.c:  207       sem_create()]:::add semid = 393228
[    leobox_ipc.c:  207       sem_create()]:::add semid = 425997
[    leobox_ipc.c:  207       sem_create()]:::add semid = 458766
[    leobox_ipc.c:  207       sem_create()]:::add semid = 491535
[    leobox_ipc.c:  207       sem_create()]:::add semid = 524304
[    leobox_ipc.c:  207       sem_create()]:::add semid = 557073
[    leobox_ipc.c:  207       sem_create()]:::add semid = 589842
[    leobox_ipc.c:  207       sem_create()]:::add semid = 622611
[    leobox_ipc.c:  207       sem_create()]:::add semid = 655380
[  122 ncc_main.c          :  177             main()]
:::[122]Thread Create[main thread]
[  122 ncc_runtimecfg.c    :  538   initRunTimeCfg()]
:::Init Run-Time Config Success.
[  122 ncc_runtimecfg.c    :  539   initRunTimeCfg()]
:::Total 4470 nodes, each node 24 bytes.
[  122 ncc_runtimecfg.c    :  540   initRunTimeCfg()]
:::Total 107280 byte for all nodes.
[  122 ncc_runtimecfg.c    :  541   initRunTimeCfg()]
:::Total 68493 byte for data.
[  122 ncc_runtimecfg.c    :  207          loadCfg()]
:::Start loadCfg
[  122 ncc_lz77.c          :  534     flash2rootfs()]
:::Load Success(/var/tmp/cfg.txt)
[  122 ncc_runtimecfg.c    :  990  setObjToDefault()]
:::set IGD_FirmwareStatus_[1,1,0,0,0] to default
/etc_ro/rcS: line 163: mp.sh: not found
starting pid 140, tty '/dev/ttyS1': '/bin/sh'
# [  122 ncc_inf.c           : 1132     ncc_inf_main()]
:::JTraceLevel=4
[  122 leobox_network.c    : 1083    socket_select()]
:::Enter pid=122,ppid=1
[leobox_network.c: 1093    socket_select()]
:::main process get thread id=1026
[  142 leobox_network.c    :  835 socket_select_hdlr()]
:::[142]Thread Create[socket_select_hdlr]
[  143 ncc_inf.c           :  959       processInf()]
:::[143]Thread Create[processInf]
================nice=-20
bind: Address already in use
[  122 ncc_main.c          :  269             main()]
:::Stop Web Access HTTP
[  122 ncc_httpd.c         :  539          httpdOp()]
:::st is null.
[  122 /opt/release/rt6856/RT288x_SDK/source/user/wolf/cameo/ncc/..
/model/dlink_810_B/objTools/ncc_objTools.c: 5095 
probeHTTPsEnable()]:::probeHTTPsEnable();
[  122 ncc_main.c          :  291             main()]
:::Start HTTPS
mini_httpd: started as root without requesting chroot(), warning only
sh: cannot create /sys/class/net/br0/bridge/tcp_allow: nonexistent directory
bind: Address already in use
[  122 ncc_main.c          :  305             main()]
:::Stop Web Access HTTPS
[  122 ncc_httpd.c         :  539          httpdOp()]
:::st is null.
mini_httpd: started as root without requesting chroot(), warning only
[  157 leobox_timer.c      :  235      timerThread()]
:::[157]Thread Create[timerThread]
[  157 leobox_timer.c      :  243      timerThread()]
:::Timer Thread Running
[  158 ncc_main.c          :   41    sendBootEvent()]
:::[158]Thread Create[sendBootEvent]
sh: cannot create /proc/sys/net/ipv4/conf/eth2.2/arp_ignore: 
nonexistent directory
[  122 ncc_fsm_boot.c      :  513             Boot()]:::=====================Start DIR_810_Boot=====================
[  122 ncc_fsm_boot.c      :  570             Boot()]:::MAC 0 = 6C198FEDF0F6
[  122 ncc_fsm_boot.c      :  571             Boot()]:::MAC 1 = 6C198FEDF0F7
switch reg write offset=3100, value=56330
switch reg write offset=3200, value=56330
switch reg write offset=3300, value=56330
switch reg write offset=3400, value=56330
switch reg write offset=3000, value=56330
Set: phy[4].reg[4] = 05e1
Set: phy[4].reg[0] = 3300
[  122 ncc_l2_independence.c:  171       swSpeedSet()]:::port = 4, speed = 0
killall: crond: no process killed
[  122 ncc_crond.c         :   54        crondConf()]:::DEBUG ON
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.
[  122 ncc_firewall.c      : 1572      reBuildMAC6()]:::reBuildMAC6()+
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.
[  122 ncc_firewall.c      : 1621      reBuildMAC6()]:::reBuildMAC6()-
ip6tables: No chain/target/match by that name.
[  122 /opt/release/rt6856/RT288x_SDK/source/user/wolf/cameo/ncc/..
/model/dlink_810_B/objTools/ncc_objTools.c: 8098 
probeFirewall6_SimpSec()]:::>>probeFirewall6_SimpSec
[  122 ncc_objAction.c     : 2609 reflash_IGD_Status_IPv6Status_()]
:::get iface eth2.2
[  122 /opt/release/rt6856/RT288x_SDK/source/user/wolf/cameo/ncc/..
/model/dlink_810_B/objTools/ncc_objTools.c: 8175 
probeFirewall6_SimpSec()]:::<<probeFirewall6_SimpSec 
readInfo(InfoV6AutoDetectWanType):0
[  122 /opt/release/rt6856/RT288x_SDK/source/user/wolf/cameo/ncc/..
/model/dlink_810_B/objTools/ncc_objTools.c: 8215 
probeFirewall6_SimpSec()]:::<<probeFirewall6_SimpSec
[  122 ncc_firewall.c      : 2236 reBuildFirewall6CPE()]:::
[Bernie debug]:tmpPreiapd =
[  122 ncc_firewall.c      : 2237 reBuildFirewall6CPE()]:::
[Bernie debug]: prepare set cpe-dynamic rule
[  122 ncc_objAction.c     : 2609 reflash_IGD_Status_IPv6Status_()]
:::get iface eth2.2
killall: wakeOnLanProxy: no process killed
[  122 ncc_firewall.c      : 4978      runFwScript()]:::===ipt run start===
[  122 ncc_firewall.c      : 4980      runFwScript()]:::===ipt run end===
[SYS][  122 ncc_firewall.c      : 5572         nfOpFunc()]
:::[nfOpFunc]Finish nf_init, 0
[  122 ncc_fsm_boot.c      :  780             Boot()]:::cfg->tzone=-128
Sat Jan  1 00:00:00 GMT 2011
[  122 ncc_fsm_boot.c      :  806             Boot()]:::Merge language pack!!
[ 4370 lang_merge.c        : 1153             main()]:::before print info
[ 4370 lang_merge.c        : 1156             main()]:::Parameters:
 ori_lang_fp: /var/tmp/lang.js
 def_lang_fp: /www/def_lang.js
[ 4370 lang_merge.c        : 1234             main()]:::save to old js file!!
[ 4370 lang_merge.c        : 1235             main()]:::save to old js file!!
[ 4370 lang_merge.c        : 1236             main()]:::save to old js file!!
sh: cannot create /proc/sys/net/ipv6/conf/ra1/disable_ipv6: nonexistent directory
sh: cannot create /proc/sys/net/ipv6/conf/rai1/disable_ipv6: nonexistent directory
[  122 ncc_status.c        : 1211     delIfaceInfo()]:::delIfaceInfo()+:iface:br0
[  122 ncc_routerlan.c     :   37 attachWanDomainName()]:::Get wan interface fail!!
[  122 ncc_routerlan.c     :   37 attachWanDomainName()]:::Get wan interface fail!!
[  122 ncc_help.c          : 1599      checkDefCfg()]:::defCfg=1
llmnr: have no available linklocal address. wait count=0
[  122 ncc_firewall.c      : 4978      runFwScript()]:::===ipt run start===
[  122 ncc_firewall.c      : 4980      runFwScript()]:::===ipt run end===
[SYS][  122 ncc_firewall.c      : 5572         nfOpFunc()]:::[nfOpFunc]Finish nf_redirect_to_index_on, 47
[  122 ncc_firewall.c      : 4978      runFwScript()]:::===ipt run start===
llmnr: have no available linklocal address. wait count=1
[  122 ncc_firewall.c      : 4980      runFwScript()]:::===ipt run end===
[SYS][  122 ncc_firewall.c      : 5572         nfOpFunc()]:::[nfOpFunc]Finish nf_lan_up, 3
[  122 ncc_help.c          : 1599      checkDefCfg()]:::defCfg=1
[  122 ncc_mdns.c          :  173         mdnsConf()]:::hnf=0
llmnr: have no available linklocal address. wait count=2
invalid option in file /var/tmp/upnpd_wan.conf line 2 : int_ifname=br0
invalid option in file /var/tmp/upnpd_wan.conf line 14 : wps_enable=1
Jan  1 00:00:06 miniupnpd[6375]: could not open lease file: 
/tmp/upnp_rdr_list
Jan  1 00:00:06 miniupnpd[6375]: HTTP listening on port 65530
No IPv6 address found for interface br0.
Jan  1 00:00:06 miniupnpd[6375]: no HTTP IPv6 address
Jan  1 00:00:06 miniupnpd[6375]: [truncated] m
Jan  1 00:00:06 miniupnpd[6375]: [truncated] m
Jan  1 00:00:06 miniupnpd[6375]: [truncated] m
Jan  1 00:00:06 miniupnpd[6375]: [truncated] m
Jan  1 00:00:06 miniupnpd[6375]: [truncated] m
Jan  1 00:00:06 miniupnpd[6375]: [truncated] m
Jan  1 00:00:06 miniupnpd[6375]: [truncated] m
Jan  1 00:00:06 miniupnpd[6375]: [truncated] m
Jan  1 00:00:06 miniupnpd[6375]: [truncated] m
Jan  1 00:00:06 miniupnpd[6375]: [truncated] m
Jan  1 00:00:06 miniupnpd[6375]: [truncated] m
Jan  1 00:00:06 miniupnpd[6375]: [truncated] m
Jan  1 00:00:06 miniupnpd[6375]: [truncated] m
Jan  1 00:00:06 miniupnpd[6375]: [truncated] m
mDNSResponderPosix: Starting in daemon mode
killall: lld2d: no process killed

***** g_wl_interface = ra0 ******

killall: proxy: no process killed
[    leobox_ipc.c:  207       sem_create()]:::add semid = 688149
[ 6392 lanmapd.c           : 2648             main()]
:::=======Lanmapd=====
[ 6392 lanmapd.c           : 2649             main()]:::iface br0
[ 6392 lanmapd.c           : 2650             main()]:::ip 192.168.0.1
[ 6392 lanmapd.c           : 2652             main()]:::ipAlias 192.168.0.1
[ 6392 lanmapd.c           : 2654             main()]:::netmask 255.255.255.0
[ 6392 lanmapd.c           : 2655             main()]:::network id 192.168.0.0
[ 6392 lanmapd.c           : 2656             main()]:::mac 6c:19:8f:ed:f0:f6
[ 6392 lanmapd.c           : 2657             main()]:::hostname dlinkrouter
[ 6392 lanmapd.c           : 2658             main()]:::hostname encode
 EEEMEJEOELFCEPFFFEEFFCCACACACAAA
[ 6392 lanmapd.c           : 2660             main()]:::aliasname shareport
[ 6392 lanmapd.c           : 2661             main()]:::aliasname encode
FDEIEBFCEFFAEPFCFECACACACACACAAA
[ 6392 lanmapd.c           : 2663             main()]:::========================
llmnr: have no available linklocal address. wait count=3
killall: crond: no process killed
killall: wscd: no process killed
Starting loop GPIO LED=9,PBC=2
[  122 ncc_fsm_boot.c      :  307  doRtInit()]
:::Send Event to open 2.4G Wlan !
[  122 ncc_EventInternal.c :  253   wlanSchedCheck()]:::no sched
llmnr: have no available linklocal address. wait count=4
llmnr: have no available linklocal address. wait count=5
llmnr: have no available linklocal address. wait count=6
llmnr: have no available linklocal address. wait count=7
llmnr: have no available linklocal address. wait count=8
llmnr: have no available linklocal address. wait count=9
[  122 ncc_fsm_boot.c      :  312         doRtInit()]
:::Send Event to open 5G Wlan !
[  122 ncc_EventInternal.c :  253   wlanSchedCheck()]:::no sched
llmnr: have no available linklocal address. wait count=10
llmnr: have no available linklocal address. wait count=11
llmnr: have no available linklocal address. wait count=12
Starting loop GPIO LED=9,PBC=2
llmnr: have no available linklocal address. wait count=13
killall: wscd: no process killed
route: ioctl 0x890b failed: File exists
libupnp: using UDP SSDP_PORT = 1900
brctl: bridge br0: Device or resource busy
brctl: bridge br0: Device or resource busy
[  122 ncc_fsm_boot.c      :  923      Boot()]:::wanCableLink = 0
[  122 ncc_help.c          : 1599      checkDefCfg()]:::defCfg=1
[  122 ncc_mdns.c          :  173         mdnsConf()]:::hnf=0
mDNSResponderPosix: Starting in daemon mode
[  122 ncc_dev_independence.c: 3892        devOpFunc()]:::get internet_cable_lose
[  122 ncc_firewall.c      : 4978      runFwScript()]:::===ipt run start===
[  122 ncc_firewall.c      : 4980      runFwScript()]:::===ipt run end===
[SYS][  122 ncc_firewall.c      : 5572         nfOpFunc()]
:::[nfOpFunc]Finish nf_80_to_404_on, 38
[  122 /opt/release/rt6856/RT288x_SDK/source/user/wolf/cameo/ncc/..
/model/dlink_810_B/objTools/ncc_objTools.c: 8069 probeULA()]:::probeULA
[  122 ncc_help.c          : 2307 copy_mac_to_eui64()]:::v6id:6e19:8fff:feed:f0f6,
[  122 ncc_help.c          : 2191    read_ipv6addr()]
::: family : 10, prefixlen : 64, flags : 192, scope : 253, index : 9
[  122 ncc_help.c          : 2209    read_ipv6addr()]
::: + fe80::6e19:8fff:feed:f0f6
[  122 ncc_help.c          : 2953 generate_default_ULA()]
:::[IPv6 Debug]Get IPv6 Link-local Address :br0 :fe80::6e19:8fff:feed:f0f6!!
[  122 ncc_help.c          : 2996 generate_default_ULA()]
:::Default ULA prefix => fd68:09d9:84e2::
[  122 ncc_status.c        : 1248    delIfaceInfo6()]:::delIfaceInfo6()+:iface:br0
[  122 ncc_status.c        : 1248    delIfaceInfo6()]:::delIfaceInfo6()+:iface:br0
[  122 /opt/release/rt6856/RT288x_SDK/source/user/wolf/cameo/ncc/..
/model/dlink_810_B/objTools/ncc_objTools.c: 8098 
probeFirewall6_SimpSec()]:::>>probeFirewall6_SimpSec
[  122 ncc_objAction.c     : 2609 reflash_IGD_Status_IPv6Status_()]
:::get iface eth2.2
[  122 /opt/release/rt6856/RT288x_SDK/source/user/wolf/cameo/ncc/..
/model/dlink_810_B/objTools/ncc_objTools.c: 8175 probeFirewall6_SimpSec()]
:::<<probeFirewall6_SimpSec readInfo(InfoV6AutoDetectWanType):0
[  122 /opt/release/rt6856/RT288x_SDK/source/user/wolf/cameo/ncc/..
/model/dlink_810_B/objTools/ncc_objTools.c: 8215 probeFirewall6_SimpSec()]
:::<<probeFirewall6_SimpSec
ip6tables: Bad rule (does a matching rule exist in that chain?).
[  122 ncc_objAction.c     : 2609 reflash_IGD_Status_IPv6Status_()]
:::get iface eth2.2
[  122 /opt/release/rt6856/RT288x_SDK/source/user/wolf/cameo/ncc/..
/model/dlink_810_B/objTools/ncc_objTools.c: 6528 probeIPv6Radvd()]
:::cfg->isdomainstatic = FALSE
[  122 /opt/release/rt6856/RT288x_SDK/source/user/wolf/cameo/ncc/..
/model/dlink_810_B/objTools/ncc_objTools.c: 6934 probeIPv6Radvd()]:::MTU: 1500
[  122 ncc_help.c          : 2191    read_ipv6addr()]
::: family : 10, prefixlen : 64, flags : 192, scope : 253, index : 9
[  122 ncc_help.c          : 2209    read_ipv6addr()]
::: + fe80::6e19:8fff:feed:f0f6
[  122 ncc_help.c          : 2953 generate_default_ULA()]
:::[IPv6 Debug]Get IPv6 Link-local Address :br0 :fe80::6e19:8fff:feed:f0f6!!
[  122 ncc_help.c          : 2996 generate_default_ULA()]
:::Default ULA prefix => fd68:09d9:84e2::
[  122 ncc_fsm_boot.c      : 1114             Boot()]:::
llmnr: have no available linklocal address. wait count=14
llmnr: have no available linklocal address. wait count=15
[  122 ncc_help.c          : 1952 is_v6defaultgw_exist()]
:::[IPv6 WARNING] Default GW not Exist.
[  122 ncc_radvd.c         :  114        radvdConf()]
:::MTU: 1500
[  122 ncc_radvd.c         :  143        radvdConf()]
:::IPV6 WARNING: LAN RADVD default lifetime is 0 due to NULL prefix.
[  122 ncc_radvd.c         :  233        radvdConf()]
:::is6rdsunset: 0, prefix:
[  122 ncc_radvd.c         :   70      radvdStart()]:::radvdStart -1
[  122 ncc_dev_v6_independence.c: 3217 devV6OpFunc()]:::pd_hint set IPv6
[  122 ncc_dev_v6_independence.c: 3288      devV6OpFunc()]
:::0:0:0:0:0:0:0:0, 56, 0, 0
[  122 ncc_status.c        : 1248    delIfaceInfo6()]:::delIfaceInfo6()+:iface:br0
[  122 ncc_status.c        : 1273    delIfaceInfo6()]:::delIfaceInfo6()+:match iface:br0
[  122 ncc_status.c        : 1248    delIfaceInfo6()]:::delIfaceInfo6()+:iface:br0
[  122 ncc_objAction.c     : 2609 reflash_IGD_Status_IPv6Status_()]
:::get iface eth2.2
[  122 ncc_fsm_boot.c      : 1299             Boot()]
:::setting v6Lan Host Filter=fe80:0:0:0:6e19:8fff:feed:f0f7!
[  122 ncc_fsm_boot.c      : 1321             Boot()]
:::===finish DIR_810_Boot===
[SYS][  122 ncc_fsm_boot.c      : 1336 Boot()]:::Boot Complate!!
[  122 ncc_EventInternal.c : 1189  doEventInternal()]:::InternalLocalTimeChange
[  122 ncc_EventInternal.c :  501 onMailSchedule()]
:::mailCfg.schedSendEnable ? 0
[  122 ncc_EventInternal.c : 1208  doEventInternal()]:::needSendLog = 0
[  122 ncc_rt5592_wlan.c   : 3083 rt5592_wlan_Stop()]:::kill wscd 2.4g
[  122 ncc_objAction.c     : 2084 ResetWirelessCounter()]:::DEBUG ON
[  122 ncc_EventInternal.c :  253   wlanSchedCheck()]:::no sched
cat: can't open '/var/run/wscd.pid.rai0': No such file or directory
kill: you need to specify whom to kill
rm: cannot remove '/var/run/wscd.pid.rai0': No such file or directory
libupnp: using UDP SSDP_PORT = 1900
brctl: bridge br0: Device or resource busy
brctl: bridge br0: Device or resource busy
Starting loop GPIO LED=9,PBC=2
route: ioctl 0x890b failed: File exists
invalid option in file /var/tmp/upnpd_wan.conf line 2 : int_ifname=br0
invalid option in file /var/tmp/upnpd_wan.conf line 14 : wps_enable=1
libupnp: using UDP SSDP_PORT = 1900
[  122 ncc_rt5592_wlan.c   : 3099 rt5592_wlan_Stop()]:::kill wscd 5g
[  122 ncc_objAction.c     : 2098 ResetWirelessCounter()]:::DEBUG ON
[  122 ncc_EventInternal.c :  253   wlanSchedCheck()]:::no sched
Starting loop GPIO LED=9,PBC=2
route: ioctl 0x890b failed: File exists
invalid option in file /var/tmp/upnpd_wan.conf line 2 : int_ifname=br0
invalid option in file /var/tmp/upnpd_wan.conf line 14 : wps_enable=1

Images

Serial (UART)

Header pins were not populated as they appear in the FCC photo.