Linksys WRT350N v1

Linksys WRT350N v1

Manuf (OEM/ODM): CyberTAN

FCC approval date: 29 September 2006
Country of manuf.: China
S/N prefix: CNQ0

Local image

Type: wireless router

FCC ID: Q87-WRT350N
IC ID: 3839A-WRT350N

Power: 12 VDC, 1.25 A
Connector type: barrel

CPU1: Broadcom BCM4705 (300 MHz)
FLA1: 8 MiB8,388,608 B 65,536 Kib 8,192 KiB 64 Mib 0.00781 GiB  (Intel JS28F640J3D-75)
RAM1: 32 MiB33,554,432 B 262,144 Kib 32,768 KiB 256 Mib 0.0313 GiB  (Nanya NT5DS8M16FS-5T × 2)

Expansion IFs: PCMCIA (32-bit), USB 2.0
PCMCIA slots: 1
USB ports: 1
Serial: yes, 5-pad header, (115200,8,N,1)

WI1 module: CyberTAN WM802-B
WI1 module IF: PCMCIA (32-bit)
WI1 chip1: Broadcom BCM4321
WI1 chip2: Broadcom BCM2055
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: Fixed Non-Removable

ETH chip1: Broadcom BCM4705
Switch: Broadcom BCM5397
LAN speed: 1GbE
LAN ports: 4
WAN speed: 1GbE
WAN ports: 1

bgn

Stock bootloader: CFE 1.0.37-1.08 BCM947XX

Stock FW OS: Linux 2.4.20

TPFirmware supported: DD-WRT • (List), OpenWrt • (List | Dev | DLs)

Default IP address: 192.168.1.1
the IP 192.168.1.1 is used by 1304 additional devices
of which 154 are Linksys devices
Default login user: blank
Default login password: admin
blank:admin credentials used by 300 additional devices
of which 143 are Linksys devices

802dot11 OUI: 00:1A:70 (9 E, 15 W), 00:1C:10 (9 E, 16 W), 00:1D:7E (10 E, 14 W)
Ethernet OUI: 00:1A:70 (9 E, 15 W), 00:1C:10 (9 E, 16 W), 00:1D:7E (10 E, 14 W)

	FCC ID
CyberTAN WM802-B	QDS-BRCM1023 Q87-WRT350N

	CPU1 brand	WI1 chip1 brand	WI1 chip2 brand
Linksys WRT350N v1	Broadcom	Broadcom	Broadcom
Linksys WRT350N v2	Marvell	Atheros	Atheros

For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.

Wireless-N Gigabit Router with Storage Link

• Support page • (Template link outdated)

Links of Interest

Flashing

NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power.

Flashing DD-WRT

On the DD-WRT Wiki

WARNING: Do not flash micro this unit!

WARNING: Requires K2.4 for DD-WRT, Do not flash anything else!

First, before you do anything else, check which version of the WRT350N you have.

If you have V1, you're in business. If you have V2, you're outta luck.

Flashing a virgin WRT350N with the default Linksys firmware will require a special "trailed" mini-build to be flashed first.

You should use a build from the BS Broadcom folder 12874 for the initial flash.

The name of this file specifically is "dd-wrt.v24_mini_wrt350n.bin".

You may proceed to flash it with a generic build next, such as Mega.bin.

Remember to do the 30/30/30 Hard Reset after every successful flash.

It is absolutely essential.

The proper process for flashing is:

Read Note 1 of the peacock announcement http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
Read Note 3 of the peacock announcement
Download dd-wrt.v24_mini_wrt350n.bin
Do a Hard reset or 30/30/30 on your router. You will not get a password renewal page as you have stock linksys firmware on the router still.
Plug a cable into the lan port of the router and your computer, and disable any wireless to the computer. Disable all firewalls and virus protection. (Setting your computer to a static IP should not be required)
Set your browser to 192.168.1.1. This will open up the linksys webgui
Enter the username admin and password admin
Go to the administration tab. Click on firmware upgrade.
BROWSE to the dd-wrt.v24_mini_wrt350n.bin file you downloaded.
Click on the upgrade button and WAIT for the upgrade successful message. Wait at LEAST 5 minutes
Power cycle your router. (very important) WAIT until you can relogin at 192.168.1.1
Do another PROPER Hard reset or 30/30/30 on your router (very important) WAIT until you can login at 192.168.1.1
Click on any tab. Reset your username/password by TYPING in a new username/password
Configure your router

You can now upgrade to any generic dd-wrt build except Micro. Be sure to always do a hard reset prior to flashing another build, do a power cycle followed by another hard reset after flashing, and NEVER re-use a configuration file from a previous build or another router. Reconfigure from scratch.

Flashing OpenWrt

On the OpenWrt Wiki

Flashing Gargoyle

From DD-WRT

DoesItMatter Wrote:

gargoyle_1.3.13-wrt350n_v1-squashfs.bin

Grab that image from the download section

Linksys WRT350N
Chipset Broadcom 4785
RAM 32 MB FLASH 8 MB

Broadcom chipsets are fairly easy to back-forth between
Gargoyle and DD-WRT

Best recommendation for steps:

download a backup current DD-WRT build you are using
backup your current DD-WRT config
reset dd-wrt to defaults
from dd-wrt GUI - flash the gargoyle.bin image
once you start the flash - wait about 5 minutes
try to login to 192.168.1.1 - defaull password = password

If you want to go back to dd-wrt

backup your current Gargoyle config
reset Gargoyle to defaults
flash the dd-wrt .bin file that you originally saved above
once again - wait about 5 minutes for flash
reload your backup config file for dd-wrt

Upgrading

Updating DD-WRT

If dd-wrt is already on the router follow these instructions. If stock firmware is on the router follow the flashing instructions.

Check for recommended builds here first.
Set your computer to a static IP of 192.168.1.7. (or to whatever subnet the router is on) Disable all firewalls and security. Disable wireless on your computer and only have the router connected to the flashing computer by the ethernet cable between the two.
Hard reset or 30/30/30 (If the router supports it, if not, reset to defults in the GUI) prior to flashing. Wait. Check for password page on re-login and change password.
Flash firmware. You can use the webgui except if you have a belkin router. (For belkin use tftp.exe to flash)
Wait...at least three minutes. Lights should return to normal. See important2, below. Failing to wait is how most people brick their routers.
Do a power cycle of the router. (Unplug the cord, count to 30 and plug it back in.)
Wait for the lights to return to normal usually about 2 minutes.
Hard reset or 30/30/30 again (If the router supports it, if not, reset to defults in the GUI). Wait. Check for the password page and re-login to change the password. Then you can reconfigure your settings manually.
Once configured set your computer back to autoIP and autoDNS.

Important1: This Hard reset or 30/30/30 works fine for Asus router, but you do have to power cycle after the reset.

Important2: After you flash the firmware, and before you do the hard reset, the router will be building some nvram settings. YOU MUST WAIT FOR THIS TO FINISH PRIOR TO DOING ANYTHING WITH THE ROUTER INCLUDING A HARD RESET. Usually, you can tell when this process is completed by the WAN light coming on, but it does take several minutes. Go have a beer. There are starting to be more and more people who BRICK their routers by not waiting until the nvram is rebuilt, PRIOR to doing a hard reset. YOU NEED TO WAIT!

JTAG-Serial Info

JTAG

JTAG Pinouts

 nTRST   1o o2	GND
   TDI   3o o4	GND
   TDO   5o o6	GND
   TMS   7o o8	GND
   TCK   9o o10	GND
 nSRST  11o o12  N/C

Serial

Serial Pinouts

 GND 5 o
 N/C 4 o
  TX 3 o ?
  RX 2 o ?
 VCC 1 o
 --------
   ? 1 o ?
   ? 2 o ?

Hyper terminal Setup in Windows XP

In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.

Putty Setup in Windows XP

After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = none
 Flow control = none
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open

DD-WRT Serial Recovery

Modified redhawk0 instructions

Print out these instructions for Off-Line use
Connect PC to router with a network cable
Configure PC with a static IP of 192.168.1.10
Connect Serial cable
Start one of the programs from above
Get TFTP ready with file selected
Use dd-wrt.v24 mini wrt350n.bin
Connect power to the router
start a rapid fire Cntl-C as you plug the router to power
type "nvram erase" w/o quotes, hit enter
type "flash -noheader : flash1.trx" w/o quotes, this starts the tftp daemon, hit enter
but have TFTP ready
Click go or start on TFTP
give it 5 minutes after it finishes
then power cycle....Hard reset or 30/30/30...then config
when it stops spitting out txt....hit the enter key...you should get a login prompt...at that point, power cycle it, hard reset...then config
you'll see it boot up

USB Info

DD-WRT USB

The USB port is where you can connect an external USB hard drive or flash drive.

Which can do a multitude of things. You can use in as a NAS, storage for a FTP

server, use Optware to run external programs like torrent software, samba for

sharing files to network, share a USB printer with network...

The list of possibilities is long, it just takes a little research.

ProFTPd is included in most the newer builds of dd-wrt.

Check the features chart to be sure.

vlan Info

DD-WRT vlan Info

WikiDevi:DD-WRT/VLAN Support

I can confirm the WRT350N v1.0 does support port-based vlan's via nvram only, the gui doesn't work. "proc/switch" is not present.

Defaults

root@DD-WRT:~# nvram show | grep vlan.ports
vlan2ports=0 8
vlan1ports=1 2 3 4 8*
size: 19676 bytes (13092 left)
root@DD-WRT:~# nvram show | grep port.vlans
port5vlans=1 2 16
port4vlans=1
port3vlans=1
port2vlans=1
port1vlans=1
port0vlans=2
size: 19676 bytes (13092 left)
root@DD-WRT:~# nvram show | grep vlan.hwname
vlan2hwname=et0
vlan1hwname=et0
size: 19676 bytes (13092 left)
root@DD-WRT:~#

Commands

root@DD-WRT:~# nvram set vlan2ports="0 4 8"
root@DD-WRT:~# nvram set vlan1ports="1 2 3 8*"
root@DD-WRT:~# nvram commit
root@DD-WRT:~# reboot

nvram

root@DD-WRT:~# nvram show | grep vlan.ports
vlan2ports=0 4 8
vlan1ports=1 2 3 8*
size: 19895 bytes (12873 left)
root@DD-WRT:~# nvram show | grep port.vlans
port5vlans=1 2 16
port4vlans=1
port3vlans=1
port2vlans=1
port1vlans=1
port0vlans=2
size: 19895 bytes (12873 left)
root@DD-WRT:~# nvram show | grep vlan.hwname
vlan2hwname=et0
vlan1hwname=et0
size: 19895 bytes (12873 left)
root@DD-WRT:~#

GUI

Reset to default before test, GUI settings do not work

root@DD-WRT:~# nvram show | grep vlan.ports
vlan2ports=0 8
vlan1ports=1 2 3 4 8*
size: 19594 bytes (13174 left)
root@DD-WRT:~# nvram show | grep port.vlans
port5vlans=1 2 16
port4vlans=2 18 19
port3vlans=1 18 19
port2vlans=1 18 19
port1vlans=1 18 19
port0vlans=2 18 19
size: 19594 bytes (13174 left)
root@DD-WRT:~# nvram show | grep vlan.hwname
vlan2hwname=et0
vlan1hwname=et0
size: 19594 bytes (13174 left)
root@DD-WRT:~#