TCP Connected Gateway

TCP Connected Gateway (600GWB)

Manuf (OEM/ODM): GreenWave Reality GL30002-TP

FCC approval date: 30 November 2011
(Est.) initial retail price (in USD): $80
Country of manuf.: China

Amazon image

ASIN
B00DYO96GI (, On Amazon, On CCC)

Type: IoT, IoT hub, JenNet wireless gateway

FCC ID: Z3M-GGL30
IC ID: 10257A-GL30002

Power: 5 VDC, 1 A
Connector type: barrel

CPU1: Applied Micro APM80186 (400 MHz)
FLA1: 32 MiB33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> (SK hynix HY27US08561A-TPCB)
FLA2: 512 KiB 0.5 MiB <br />524,288 B <br />4,096 Kib <br />4 Mib <br />4.882812e-4 GiB <br /> (Macronix MX25L4006E)
RAM1: 64 MiB67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (SK hynix H5PS5162GFR-S6C)

Expansion IFs: none specified
Serial: yes, 2-pads

WI1 chip1: NXP JN5148
WI1 802dot11 protocols: ZigBee
WI1 antenna connector: none

ETH chip1: Applied Micro APM80186
ETH chip2: Realtek RTL8201CP
LAN speed: 100M
WAN speed: 100M
WAN ports: 1

ZigBee

Additional chips
CMOS Real Time Clock;NXP;PCF8563;;1;

Stock bootloader: U-Boot 2009.08

Stock FW OS: Linux 3.5.3

Flags: ZigBee, RTC, IoT

Default IP address: acquired via DHCP
the IP acquired via DHCP is used by 207 additional devices
of which 0 are TCP devices
Default login user: root
Default login password: thinkgreen

802dot11 OUI: none specified
Ethernet OUI: D4:A9:28

For a list of all currently documented Applied Micro (AMCC) SoC's with specifications, see Applied Micro.
For a list of all currently documented NXP (Freescale) SoC's with specifications, see NXP.

---

TCP 600GWB Connected at Home Wireless Lighting Gateway

Install Guide

Wireless is 802.15.4 JenNet used to control wireless lighting.

Smaller flash is used by wireless micro-controller.

Links

• Understanding the Greenwave Reality Gateway
• On exploitee.rs

Disassembly with photos of circuit board

Dropbear SSHD, UART

• Troubleshooting • >>

SOME TIPS FOR GETTING YOUR TCP / Greenwave Systems / Greenwave Reality LIGHTBULBS AND GATEWAY TO FIND EACH OTHER Troubleshooting: Light Bulb Not Responding During Installation: When you add a new light bulb to the network (or if you add a previously existing light bulb that you removed from the network), the light bulb should brighten and dim during the installation process to indicate that it is searching for a network. If for any reason the light bulb does not brighten and dim (if it remains full bright), then turn power to the light fixture off and on four times consecutively to reset the light bulb. The light bulb should then start to brighten and dim once it is reset, which is usually within 10 seconds after the fourth off/on cycle. Light Bulb Accidentally Removed from Network: It is possible for a network light bulb to be accidentally removed from the network. For example, if someone turns power off and on four times consecutively to the light fixture, the attached light bulb will reset and remove itself from the network. If this happens, follow the procedure in the Light Bulb Tasks chapter to add a new light bulb to the network. Resetting Your Light Bulbs: If you are unable to fix issues that arise with your lighting system, you can reset your light bulbs as a last resort. To do so, follow the procedure in the Light Bulb Tasks chapter to remove light bulbs from the network, followed by the procedure to add a new light bulb to the network. Source